OMRON E5CN-HC2BFD User's Manual (Communications Functions) PDF

Appearance: Shielded, M12.
Sensing distance: 4 mm.
Output: NPN.
Model: Operation mode NC.
Aluminum and Iron Both.
Detectable from Long Distances. Fitting materials: Stainless steel(SUS304) E5CN-HC2BFD PDF.
Count: 1 .
Accessories: Description, Slotted/Phillips screws M3 × 8,
(with spring and plain washers);
Material, Stainless steel (SUSXM7), Stainless steel (SUS304);
Count, 2.
Applicable sensor (mounting pitch on sensor side): E3Z pre-wired model E5CN-HC2BFD
Page: Dimensions, 14. Size: M8(Stainless steel)(See note 2.); Single; Shielded.
Sensing distance: 1.5 mm.
Connecting method (See note 1.): M8 Connector (3-pin) E5CN-HC2BFD PDF.
Body length: Short.
Output configuration: NPN.
Operation mode NO.
A new generation in global applications. Size: 96 x 96mm.
Ontology: terminal type, temperature input type.
Category: control output 1 point type (power supply AC100 ~ 240V).
Shell color: black.
Control output: voltage output (SSR driver) E5CN-HC2BFD PDF.
Control mode: standard or heating cooling.
Auxiliary output points: 3 points.
Heater with broken wire, SSR fault, heater over current detection function /ES1B power supply: single phase heater with detection function.
Event input points: -.
Transfer output: - OMRON User's Manual.
Communication: RS-232C.
The general temperature controller 96mm, 48 * 96mm square has been upgraded to improve the performance and function of /.
Indicates that the accuracy of the upgrade, increase the function of prevention and maintenance, further enhance the performance.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/STOP, alarm), interactive display PV/SV OMRON User's Manual.
Increase the number of control output ON/OFF counting function, can prevent the maintenance of temperature controller internal relay.
Increased the 3 segment display, which can display the current value / target / operation OMRON User's Manual.
Increased the PF key, the distribution of automatic / manual, RUN/STOP, etc., can be a key operation. Name: Basic Unit (temperature control) *1.
Power supply voltage: 24 VDC supplied from the End Unit E5CN-HC2BFD Manual.
No. of control points: 4.
Control outputs 1 and 2: Voltage output: 2 points (for SSR drive) *2.
Control outputs 3 and 4: Voltage output: 2 points (for SSR drive) *2.
Auxiliary output: None.
Functions: burnout Heater alarm, None; Event inputs, None .
Communications functions: G3ZA connection port: RS-485,
From End Unit: Port A or port B: RS-485.
Input type: Thermocouple, platinum resistance thermometer,
analog voltage, and analog current selectable for each channel.
Terminal: Screw-less clamp.
In-panel Temperature Controller with Flexible,
Modular Design and Wide Integration with Host,
Devices.
The compact modular structure enables construction of temperature,
systems optimally suited to the application.
Connection can be made to a Programmable Controller without any,
programming required, reducing the number of steps required in ladder,
programming design.
One fully universal-input Unit includes a thermocouple, platinum-resistance,
thermometer, and analog input for easy selection and reduced inventory,
requirements.
Connect directly to thee G3ZA Multi-channel Power Controller using,
optimum cycle control for high-accuracy regulation with minimal noise E5CN-HC2BFD User's Manual.
Autotuning (AT) can be used for independent heating/cooling PID control.
Self-tuning (ST) can be used to calcullate the PID constants with the step,
response method E5CN-HC2BFD Manual.
Up to 16 Temperature Controllers can be connected to a single DeviceNet,
Communications Unit.