Yaskawa SGMSV-50D3A6S USER'S MANUAL (Setup Rotational Motor) PDF

Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard SGMSV-50D3A6S PDF.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGMSV-50D3A6S0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGMSV-50D3A6S PDF.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part) SGMSV-50D3A6S PDF.
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationType: SGDH type drive.
Capacity: 0.2kw.
Voltage: single phase 200V Yaskawa USER'S MANUAL.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method Yaskawa USER'S MANUAL.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction SGMSV-50D3A6S Manual.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data Yaskawa USER'S MANUAL. Sigma -V series servo motor SGMSV.
Rated output: 1.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat ressistance grade: F SGMSV-50D3A6S USER'S MANUAL.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMSV-50D3A6S Manual.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation