MITSUBISHI FX3G-14MT/DS PROGRAMMING MANUAL (Basic & Applied Instructions Edition) PDF

Max input / output points: 30 points.
Power supply voltage: 24VDC.
Input points: 16 points.
Output points: 14 points.
Output type: relay.
Power consumption (W): 8 FX3G-14MT/DS PDF.
Weight (kg):0.35.
Size (WxHxD) mm:100x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device FX3G-14MT/DS
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor FX3G-14MT/DS PDF.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.
All equipment is digital input and output point FX3G-14MT/DS PDF.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator. Input points: 32 points
Input mode: DC24V (drain type) MITSUBISHI PROGRAMMING MANUAL.
Connection status: connector.
In order to extend the input output of the device.
Also has a built-in power supply products.
The maximum number of points for the input and output is 256.
Expansion module: up to 16 units (in addition to the power expansion module)
The total number of CC-Link, AnyWireASLINK, and Bitty series of remote I/O is 512 points MITSUBISHI PROGRAMMING MANUAL. Power: 280kw FX3G-14MT/DS Manual.
Voltage: 400V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function MITSUBISHI PROGRAMMING MANUAL. Cable flat cable;
Connector with 20 pin installed at both ends of the fuse.
Length 5M. Max input / output points: 14 points.
Power supply voltage: DC24V.
Input points: 8 points.
Output points: 6 points.
Output type: Transistor (source).
Power consumption (W): 19.
Weight (kg):0.3.
Size (WxHxD) mm:60x90x75.
Positioning and pulse output functions: a PLC cell can output 2 point 100KHz pulses at the same time.
PLC is equipped with 7 special positioning instructions,
Including zero return, absolute or relative address expression and special pulse output control.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no baattery, easy to maintain FX3G-14MT/DS PROGRAMMING MANUAL.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor.
The series PLC can not be brought with the expansion module, but can be installed by the BBD board to extend a small amount of I/O FX3G-14MT/DS Manual.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication.