OMRON E5CN-HC201-W-FLK INSTRUCTION Manual PDF

Sensing method: Through-beam type.
Sensing distance(slot width): 5 mm.
Output type: NPN output.
Output configuration: Dark-ON.
Cable length: 1 m.
Photomicrosensor with built-in,
amplifier and attached cable reduces,
external light interference E5CN-HC201-W-FLK PDF.
Light modulation effectively reduces external light interference.
Wide operation voltage range: 5 to 24 VDC.
Easy operation monitoring with bright light indicator E5CN-HC201-W-FLK Fitting materials: Stainless steel (SUS304).
Count: 1.
Accessories: Description, Holder (upper) Holder,
(lower) Pipe Bolts M4 × 12 with Hexagonal holes,
Bolts M4 × 30 with hexagonal holes,
Phillips screws M3 × 12 (with spring and plain washers),
Spring washer M4 Plain washer M4 Nuts M4;
Material, Heat-resistant ABS resin, 66 nylon,
Stainless steel (SUS304), Iron, nickel plating,
Iron, nickel plating, Stainless steel (SUS304),
Iron, nickel plating, Iron, nickel plating,
Iron, nickel plating; Count, 1, 1, 1, 2, 1, 2, 1, 1, 3 E5CN-HC201-W-FLK PDF E5CN-HC201-W-FLK PDF.
Applicable sensor (mounting pitch on sensor side): E3Z (25.4) E39-R1/E39-R3.
Page: Dimensions, 9. Appearance: Unshielded, M30.
Sensing distance: 15 mm.
Output configuration: DC 3-wire, PNP.
Model: Operation mode, NC OMRON INSTRUCTION Manual.
General-purpose Threaded.
Capacitive Sensor.
Product lineup with M12, M18, and M30 models.
Fixed sensing distance requires no sensitivity adjustment. Appearance: Shielded, M30.
Sensing distance: 8 mm.
Output configuration: DC 2-wire.
Model: Operation mode, NO.
Chip-immune Inductive.
Proximity Sensor OMRON INSTRUCTION Manual.
Correct operation even with aluminum or iron chips sticking,
to the Sensor.
Only the sensing object is detected.
Pre-wired Smartclick Connector Models also available. E32-TC200F4R type: standard type; soft (new standard),
Specialty: M3 screw (small) with casing,
Shape / detection distance (mm): 160; 130; 75 (30),
Standard test object
(minimum test object) (mm) 1: 0 OMRON INSTRUCTION Manual. E5CN-HC201-W-FLK Manual. 5 (0.005),
Fiber element for meeting diversified needsSize: 96 x 96mm.
Control output 1: voltage output (SSR driver).
Control output 2:--.
Auxiliary output: 2 independent points.
Power supply voltage: AC/DC24V.
Terminal shape: screw terminal table type.
Input category: full range multi input.
Heating wire break, SSR fault detection function: 1 points.
Communication: RS-485.
Event input: 6 points.
Remote SP input: there.
Transfer output: have.
Large screen display white PV legible. From selection to setting and operation are simple and easy to use.
Full capacity, function and performance of I/O. Suitable for more applications.
E5AC white LCDPV display height is about 25mm.
The upper panel and the front panel are equipped with tool ports.
With the communication conversion line (sold separately) connected to the computer to establish the controller without the need to install the wire for power supply.
Easy to install CX-Thermo (sold separately).
50ms high speed sampling period.
Model can be equipped with up to 4 point auxiliary output, 6 point event input,
1 point transfer output and remotee SP input, suitable for a wide range of applications E5CN-HC201-W-FLK INSTRUCTION Manual.
The main body is short, the thickness is only 60mm.
Easy to use programmable logic controller (PLC) is connected to the programmable logic controller (PLC).
The temperrature controller is connected to each other by using the component communication E5CN-HC201-W-FLK Manual.
A new type of proportional control allows you to control the valve.