MR-J4W2-44B Multi axis servo drive MITSUBISHI MR-J4W2-44B

The length of the line: 5M.
IP level: IP65.
Bending life: high bending life.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). Content: CNP2 connector two.
Purpose: MR-JE-200B to MR-JE-300B, MR-JE-200A to MR-JE-300A with.
Multi axis integrated servo amplifier MR-J4W2-44B.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0.4kw.
Interface: SSCNET III /H MR-J4W2-44B.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost MR-J4W2-44B.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product MITSUBISHI MR-J4W2-44B. 1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 1.0kw.
Interface: General purpose.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode MITSUBISHI MR-J4W2-44B.
Servo amplifier supporting universal interface.
Servo amplifier for universal interface.
Speed / torque control of position control and analog voltage command can be carried out by using pulse train command MITSUBISHI MR-J4W2-44B.
Support Max instruction pulse frequency 4 Mpulses/s.
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting. MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 22.0kw.
SSCNET interface.
Voltage: 3 phase AC200VAC or single phase AC230V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connection method reduces the routing time and helps to prevent noise.
Even in the MELSERVO-J2-SUPER series products using high resolution coding staandards, the command frequency is no limit MR-J4W2-44B.
It is only necessary to add a battery on the servo amplifier, which can form the absolute value system.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.