SGM7J-A5AFC6E Yaskawa SGM7J-A5AFC6E Cantilever state and moment of inertia Rotary servo motor

Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.1kw.
Power supply voltage: single phase AC100V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space SGM7J-A5AFC6E.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer SGM7J-A5AFC6E.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedCapacity type of direct drive servo motor SGMCS SGM7J-A5AFC6E.
Rated torque: M \/ 150N.
Servo motor outside diameter size: 360mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M Yaskawa SGM7J-A5AFC6E.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min) Yaskawa SGM7J-A5AFC6E.
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment Yaskawa SGM7J-A5AFC6E.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
No speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal, with the brake (DC24V).
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tuning time to ensure performance.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sennsor SGM7J-A5AFC6E.
Monitor the temperature of the product directly through the sensor, as soon as possible to detect and prevent failure.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure