Brand sort
OMRON ZS-XC15CR
next one: 
Last one: OMRON ZS-XC15CR
Type: Shielded.
Appearance: Flat, 30 × 14 × 4.8 mm.
Sensing distance: 5 mm.
Repeat accuracy: 2 μm.
Cable specification: Free cutting .
Proximity Sensor with Separate.
Amplifier Enables Easily Making High.
precision Sensitivity Settings.
Wide variety of Sensor Heads to select according to the,
application . Flexible cables are used between Preamplifiers,
and Amplifier Units of the Sensor Heads ZS-XC15CR
High resistance to changes in ambient temperature.
Temperature characteristics of 0.08%/°C (for 5.4-dia. models).
Make simple and reliable detection settings with micron,
level precision using the teaching function.
Check the sensing excess gain level on the digital display ZS-XC15CR.
Support for high-precision positioning and screening with,
fine positioning to maximize variations .
The E2C-EDA0 supports an EtherCAT Sensor,
Communications Unit or CompoNet Sensor,
Communications Unit. Terminal: Screw terminal (-B).
Actuator: Short spring plunger.
High-capacity Switch Capable of,
Handling 20 A Loads with Large.
Inrush Currents.
Same shape as OMRON Z Basic Switches except in pin,
plunger position, yet endures inrush currents as large as 75 A ZS-XC15CR. Appearance: Knob-type Selector Switch A22W,
LED lighting (without Voltage Reduction Unit).
Number of notches: 3 notches.
Resetting method: Manual.
Output: SPST-NO + SPST-NO.
Operating voltage: 12 VAC/VDC.
Illumination color: R (red); Y (yellow); G (green); A (blue).
Install in 22-dia. or 25-dia. Panel Cutout.
Lever for easily mounting and removing the Switch Unit.
Finger protection mechanism on Switch Unit provided as a standard feature.
Use 25-dia. ring to install in 25-dia. panel cutouts.
Mounted using either open-type (fork-type) or closed-type,
(round-type) crimp terminals.
IP65 oil resistance (non-lighted models).
IP65 (lighted models). Category: power FET MOS relay output.
Points: 16 points (1a * 16).
Public connector side treatment: NPN (corresponding to the source of public).
Rated voltage: DC24V.
Pay attention to the use of convenience and space saving,
Relay terminal for 16 point output.
The terminal block is a long and thin type with a width of 135 * Deep 40mm.
It can be easily connected to the common end with the iindependent contact and shoort circuit chip ZS-XC15CR.
Terminal units for power supply wiring processing can be extended.
M3.5 can be used with the Y fork type of the compression terminal (terminal width 6.2mm).
Can not use the tool to remove the relay. Relay replacement operation is siimple ZS-XC15CR.
Equipped with relay type and power FET MOS relay mounted type.
With action indication LED.
DIN guide rail installation, screw mounting common.
ZS-XC15CR Operation manual / Instructions / Catalog download link: /searchDownload.html?Search=ZS-XC15CR&select=5
Appearance: Flat, 30 × 14 × 4.8 mm.
Sensing distance: 5 mm.
Repeat accuracy: 2 μm.
Cable specification: Free cutting .
Proximity Sensor with Separate.
Amplifier Enables Easily Making High.
precision Sensitivity Settings.
Wide variety of Sensor Heads to select according to the,
application . Flexible cables are used between Preamplifiers,
and Amplifier Units of the Sensor Heads ZS-XC15CR
High resistance to changes in ambient temperature.
Temperature characteristics of 0.08%/°C (for 5.4-dia. models).
Make simple and reliable detection settings with micron,
level precision using the teaching function.
Check the sensing excess gain level on the digital display ZS-XC15CR.
Support for high-precision positioning and screening with,
fine positioning to maximize variations .
The E2C-EDA0 supports an EtherCAT Sensor,
Communications Unit or CompoNet Sensor,
Communications Unit. Terminal: Screw terminal (-B).
Actuator: Short spring plunger.
High-capacity Switch Capable of,
Handling 20 A Loads with Large.
Inrush Currents.
Same shape as OMRON Z Basic Switches except in pin,
plunger position, yet endures inrush currents as large as 75 A ZS-XC15CR. Appearance: Knob-type Selector Switch A22W,
LED lighting (without Voltage Reduction Unit).
Number of notches: 3 notches.
Resetting method: Manual.
Output: SPST-NO + SPST-NO.
Operating voltage: 12 VAC/VDC.
Illumination color: R (red); Y (yellow); G (green); A (blue).
Install in 22-dia. or 25-dia. Panel Cutout.
Lever for easily mounting and removing the Switch Unit.
Finger protection mechanism on Switch Unit provided as a standard feature.
Use 25-dia. ring to install in 25-dia. panel cutouts.
Mounted using either open-type (fork-type) or closed-type,
(round-type) crimp terminals.
IP65 oil resistance (non-lighted models).
IP65 (lighted models). Category: power FET MOS relay output.
Points: 16 points (1a * 16).
Public connector side treatment: NPN (corresponding to the source of public).
Rated voltage: DC24V.
Pay attention to the use of convenience and space saving,
Relay terminal for 16 point output.
The terminal block is a long and thin type with a width of 135 * Deep 40mm.
It can be easily connected to the common end with the iindependent contact and shoort circuit chip ZS-XC15CR.
Terminal units for power supply wiring processing can be extended.
M3.5 can be used with the Y fork type of the compression terminal (terminal width 6.2mm).
Can not use the tool to remove the relay. Relay replacement operation is siimple ZS-XC15CR.
Equipped with relay type and power FET MOS relay mounted type.
With action indication LED.
DIN guide rail installation, screw mounting common.
ZS-XC15CR Operation manual / Instructions / Catalog download link: /searchDownload.html?Search=ZS-XC15CR&select=5
...more relevant model market price >>>>
Related products
Related download