Home
>> Products
>> MITSUBISHI
>> Inverter
>> FR-A800 series inverter
>> FR-A820 inverter 3 phase 200V
>> FR-A820-30K-1(FR-A820-01540-2-60) Three phase 200V grade frequency converter MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60)
FR-A820-30K-1(FR-A820-01540-2-60) Three phase 200V grade frequency converter MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60)
Brand:
MITSUBISHI
Name: Three phase 200V grade frequency converter
Model: FR-A820-30K-1(FR-A820-01540-2-60)
MITSUBISHI inverter series: FR-A820.
Voltage level: three phase 200V.
Power: 30kw.
SLD converter rated current: 154A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
Parameters can be selected by 4 different rated current and different overload rating (SLD (ultra light load) rated, LD (light load) rating, ND (general load) rating, HD (weight).
Type load) for selection.
You can choose the most suitable frequency converter for use; and by selecting a transducer with a SLD or LD rated level,
Be able to reduce the size of the device (compared with the FR-A700 series, to reduce the volume of equipment).
For applications that require high torque at low speeds, the HD rating is the most suitable.
The controller is used to control and monitor the frequency converter through the network.
Standard corresponding RS-485 communication (MITSUBISHI converter protocol, Modbus-RTU protocol) data transmission speed up to 115200bps.
...More relevant models >>>>
Name: Three phase 200V grade frequency converter
Model: FR-A820-30K-1(FR-A820-01540-2-60)
MITSUBISHI inverter series: FR-A820.
Voltage level: three phase 200V.
Power: 30kw.
SLD converter rated current: 154A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
Parameters can be selected by 4 different rated current and different overload rating (SLD (ultra light load) rated, LD (light load) rating, ND (general load) rating, HD (weight).
Type load) for selection.
You can choose the most suitable frequency converter for use; and by selecting a transducer with a SLD or LD rated level,
Be able to reduce the size of the device (compared with the FR-A700 series, to reduce the volume of equipment).
For applications that require high torque at low speeds, the HD rating is the most suitable.
The controller is used to control and monitor the frequency converter through the network.
Standard corresponding RS-485 communication (MITSUBISHI converter protocol, Modbus-RTU protocol) data transmission speed up to 115200bps.
Superior high efficiency IPM motor.
Output power: 37kw.
Rated speed: 1500r/min.
Voltage level: 200V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60). MITSUBISHI inverter FR-L740 series.
Voltage level: three phase 400V FR-A820-30K-1(FR-A820-01540-2-60)
Frequency converter capacity: 30KW.
Integration of the three works the core technology, the outstanding performance of reeling, release the high cost of bright light.
Wide range of professional use and advanced control.
Professional built-in function to ensure the constant material tension, suitable for the application of printing and packaging industry MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
Fusion application of the tension products of MITSUBISHI by inverter.
Suitable for tension control of high precision cable and material processing occasions.
Professional function to ensure the safe operation of textile machinery equipment,
The spinning quality and production efficiency are improved. The application of textile machinery and equipment. Voltage level: three phase 400V MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
Applicable motor capacity: 355kw.
Substrate coating: have.
Built in DC reactor.
The operating frequency of the fixed alternating current is converted to DC power. Power: 0.4kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective meeasures and cooling FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between thhe short circuit chip, in addition to connecting the DC reactor MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
The installation of thermal relay, to avoid overheating and burn the braking resistor.
Output power: 37kw.
Rated speed: 1500r/min.
Voltage level: 200V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60). MITSUBISHI inverter FR-L740 series.
Voltage level: three phase 400V FR-A820-30K-1(FR-A820-01540-2-60)
Frequency converter capacity: 30KW.
Integration of the three works the core technology, the outstanding performance of reeling, release the high cost of bright light.
Wide range of professional use and advanced control.
Professional built-in function to ensure the constant material tension, suitable for the application of printing and packaging industry MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
Fusion application of the tension products of MITSUBISHI by inverter.
Suitable for tension control of high precision cable and material processing occasions.
Professional function to ensure the safe operation of textile machinery equipment,
The spinning quality and production efficiency are improved. The application of textile machinery and equipment. Voltage level: three phase 400V MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
Applicable motor capacity: 355kw.
Substrate coating: have.
Built in DC reactor.
The operating frequency of the fixed alternating current is converted to DC power. Power: 0.4kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective meeasures and cooling FR-A820-30K-1(FR-A820-01540-2-60) MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between thhe short circuit chip, in addition to connecting the DC reactor MITSUBISHI FR-A820-30K-1(FR-A820-01540-2-60).
The installation of thermal relay, to avoid overheating and burn the braking resistor.
...More relevant models >>>>
Last one: MITSUBISHI Three phase 200V grade frequency converter FR-A820-22K-1(FR-A820-01250-2-60)
next one: MITSUBISHI Three phase 200V grade frequency converter FR-A820-37K-1(FR-A820-01870-2-60)
Related download
Related model