LK166
Home >> Products >> MITSUBISHI >> CC-Link module >> Other CC-Link modules >> MIL connector type output module CL2Y16-TP1M1V MITSUBISHI CL2Y16-TP1M1V

MIL connector type output module CL2Y16-TP1M1V MITSUBISHI CL2Y16-TP1M1V

Brand: MITSUBISHI
Name: MIL connector type output module
Model: CL2Y16-TP1M1V
Output type: transistor output, drain type.
Output points: 16 points.
OFF leakage current: 0.1mA.
Output protection function.
Rated load voltage / current: DC12V/DC24V/0.1A.
External connection: 1 wire.
MIL connector type.
Minimum size of industry.
Relay terminal, terminal station conversion module and electromagnetic valve, etc. are connected to a simple MIL connector.
Simply remove the connector can be replaced with a simple module.
Additional module power supply, I/O power sharing.
No additional I/O power supply, you can reduce the cost and set space.

Output type: transistor output, drain type.
Output points: 16 points.
OFF leakage current: 0.1mA.
Output protection function: No.
Rated load voltage / current: DC12V/DC24V/0.5mA.
External connection: 2 wire.
Type of input and output terminal.
Using 2 pieces of structure of the terminal units, maintenance can be maintained in the same line under the condition of the replacement module MITSUBISHI CL2Y16-TP1M1V CL2Y16-TP1M1V Enter 16 points: 24VDC.
Response time 1.5ms.
Waterproof type.
4 wire type.
Waterproof connector type.
MITSUBISHI PLC hardware implementation
Hardware implementation is mainly for the control cabinet and other hardware design and field construction.
Design control cabinet and the operating table and other parts of the electrical wiring diagram and wiring diagram MITSUBISHI CL2Y16-TP1M1V.
Electrical interconnection diagram of each part of the design system.
According to the construction drawings of the site wiring, and carry out a detailed inspection.
Because the program design and hardware implementation can be carried out at the same time,
So the design cycle of the MITSUBISHI PLC control system can be greatly reduced.
MITSUBISHI PLC online debugging MITSUBISHI CL2Y16-TP1M1V.
On-line debugging is the process that will through the simulation debugging to further carry on the on-line unification to adjust.
On-line debugging process should be step by step,
From MITSUBISHI PLC only connected to the input device, and then connect the output device, and then connect to the actual load and so on and so on step by step CL2Y16-TP1M1V MITSUBISHI.
If you do not meet the requirements, the hardware and procedures for adjustment CL2Y16-TP1M1V MITSUBISHI.
Usually only need to modify the part of the program can be. Voltage input range: due to different connection models, the maximum DC28.8V.
External connection mode: module power supply: Terminal 3 pin (M3 screw), communication line / module power supply unit CL2Y16-TP1M1V MITSUBISHI.
When power supply from the external power supply (customer owned) to the CC-LINK/LT system, the whole system can be stable power supply. Input type: DC input, negative public end.
Input points: 8 points.
Enter the response time: 1.5ms the following.
Rated input voltage / current: DC24V/5mA.
Output form: transistor output, source.
Output pointss: 8 points CL2Y16-TP1M1V.
OFF leakage current: 0.1mA.
Output protection function.
Rated load voltage / current: DC24V/DC24V/0.1A.
External connection: 3 line /2 line type.
Sensor connector type (E-CON type).
Using industry standard E-CONN type MITSUBISHI CL2Y16-TP1M1V.
Simple wiring through sensor connector.
When installing the module can choose to use the DIN guide rail or screw mounting.
3 wire sensor input.


...More relevant models >>>>