Memory card FX-EEPROM-4 MITSUBISHI FX-EEPROM-4

Input points: 36 points.
Output points: 24 points.
Power supply voltage: AC240-360V.
Output type: relay output.
Built in CPU, power supply, input and output. While maintaining the convenience of FX1N while improving performance.
Special adaptor and function expansion board can be installed and used FX3 series MITSUBISHI FX-EEPROM-4.
High speed operation.
Basic instructions: 0.21 s/ instruction.
Application instruction: 0 FX-EEPROM-45 s/ instruction.
Large capacity memory.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function. Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Input and output points: 40 points.
Power supply: DC24V.
Input points: 24 points.
Output points: 16 points MITSUBISHI FX-EEPROM-4.
Output form: transistor output (source).
Power consumption: 25W.
Weight: 0.7KG.
Outline dimension: 130x90x86mm.
FX3GE on the performance of the FX3GA increased analog input / output and Ethernet communication and other built-in features.
Applicable to a wide variety of applications.
Basic unit: 24/40 point.
Third generation standard model.
High flexibility.
Suitable for small scale control of high cost PLC MITSUBISHI FX-EEPROM-4.
Control points to 128 points, the use of CC-Link remote I/O can control the maximum 256 points.
A versatile PLC.
Built in CPU, power supply, input and output, analog input and output, Ethernet port, can be used immediately after the purchase FX-EEPROM-4 MITSUBISHI.
High speed operation.
Basic instructions: 0.21 s/ instruction.
Application instruction: 0.5 s/ instruction FX-EEPROM-4 MITSUBISHI.
Large capacity memory.
Built in program memory 32000 steps.
EEPROM memory cartridge with program transfer function. Max input / output points: 48 points.
Supply voltage: 100 - 240VAC.
Input points: 24 points.
Output points: 24 points.
Output type: Triac.
Power consumption: 50VA.
Weight (kg):0 FX-EEPROM-4 MITSUBISHI. 85.
Size (WxHxD) mm:182x90x87.
Since the FX2n series have the following features: the maximum range of inclusive of the standard features, program execution faster, the full complement of communication function, suitable for different countries in the world, and the power to meet a large number of special function modules of individual needs,
It can provide maximum flexibility and control capability for your factory automation applications.
Control 16~256 point.
Built in 8K capacity of the RAM memory, the maximum can be extended to 16K.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable.
Developed a range of special function modules to meet the needs of different - analog I/O, high speed counter.
Positioning control to achieve the 16 axis, the pulse train output or for the J and K type thermocouple or Pt sensor developed the temperature module.
A total of 8 special function modules can be configured for each FX2n main unit.
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, usiing a eight digit password to protect your program FX-EEPROM-4.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application off the continuous scan time MITSUBISHI FX-EEPROM-4.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).