Home
>> Products
>> OMRON
>> Power/other peripheral devices
>> Power / equipment protection equipment
>> Protective equipment for equipment
>> OMRON K8AC-H22PN-FLK Digital Heater Element Burnout Detector
OMRON K8AC-H22PN-FLK Digital Heater Element Burnout Detector
Brand:
OMRON
Name: Digital Heater Element Burnout Detector
Model: K8AC-H22PN-FLK
Power supply voltage: 100 to 240 VAC.
Heater control method: Phase control Cyclic control.
Input specifications: Two current inputs,
(for either single phase or threephase).
Output specifications: Two transistor outputs.
Communications output: RS-485.
Current input range: 2.00 to 22.00 A.
A high-precision Heater Element.
Burnout Detector compatible with a,
wide-range of heater control methods.
Push-in terminals reduce the workload.
Scaling.
NPN or PNP equivalent output.
Lineup includes models compatible with many heater control methods,
including ON/OFF control, phase control, and cyclic control.
High-precision heater burnout alarm with digital measurement.
Contributes to preventative maintenance.
If the gate function is disabled, the gate input can be used as an,
undercurrent/overcurrent relay or for motor or lamp loads.
Undercurrent detection values can be set separately for CT1 and CT2.
CE marking and cUL certified (K8AC-H2@@@).
...More relevant models >>>>
Name: Digital Heater Element Burnout Detector
Model: K8AC-H22PN-FLK
Power supply voltage: 100 to 240 VAC.
Heater control method: Phase control Cyclic control.
Input specifications: Two current inputs,
(for either single phase or threephase).
Output specifications: Two transistor outputs.
Communications output: RS-485.
Current input range: 2.00 to 22.00 A.
A high-precision Heater Element.
Burnout Detector compatible with a,
wide-range of heater control methods.
Push-in terminals reduce the workload.
Scaling.
NPN or PNP equivalent output.
Lineup includes models compatible with many heater control methods,
including ON/OFF control, phase control, and cyclic control.
High-precision heater burnout alarm with digital measurement.
Contributes to preventative maintenance.
If the gate function is disabled, the gate input can be used as an,
undercurrent/overcurrent relay or for motor or lamp loads.
Undercurrent detection values can be set separately for CT1 and CT2.
CE marking and cUL certified (K8AC-H2@@@).
Connection method: Embedded model.
Pin shape: Solder cup pins.
Applicable wires: AWG26 max.
Minimum order: 200.
Small Round Water-resistive.
Connectors.
Water-resistive, compact connector meets IP67 requirements.
Conventional M8 screw-mounting models are available along with,
S8 snap-in models that connect and disconnect with one touch OMRON K8AC-H22PN-FLK.
Ideal for a wide variety of FA and OA applications K8AC-H22PN-FLK
Connectors on both cable ends require no harness work.
Some new M8 models with 3 or 5 poles. Cable length L: 3.0 m.
Connect Connector-Terminal,
Block Conversion Units (XW2@) to,
I/O Units for Programmable,
Controllers with one touch. I/O classification: Output.
I/O points: 16.
Internal I/O circuit common: PNP (– common) OMRON K8AC-H22PN-FLK.
Rated voltage: 12 VDC, 24 VDC.
Single Cable Connection to PLC Means.
Space is Saved and Less Control Panel.
Wiring is Required.
Compact size: 182 (W) 85 (D) 68 (H) mm,
(8-point Output Block width is 102 mm).
Connects to the PC through the connecting cable,
(G79 Series) and connector, and requires only a,
snap-in operation.
Surge suppressor circuit built-in OMRON K8AC-H22PN-FLK.
Immediate recognition of I/O signal status using,
LED operation indicators.
G3TA I/O Solid-state relay can be mounted instead,
of G7T.
Mounts easily on a DIN track.
Approved by UL, CSA (except for G7TC-OC16-1). Servo trunk unit.
Product Name: servo relay unit.
Application unit: FQM1-MMA22/MMP22, CS1W-HCP22-V1.
Specifications: -.
Axis number: biaxial.
The connector and terminal of the relay unit are integrated into a whole,
Save the wiring servo drive and position control unit.
Servo driver and control signal of position control unit,
Simple wiring on terminal stage.
The connector without soldering, with only a screwdriver can wiring.
Dedicated connection cable between units.
DIN guide rail installation, the rapid installation, screw installation of two methods.
M3.0 thread terminals attached with a special plate signal.
The terminal can be confirmed by the signal name. Terminal/mounting: Plug-in/DIN rail via socket.
Control voltage: 100/110 VDC.
Under currennt detection: Instantaneous type K8AC-H22PN-FLK.
Solid-state, Plug-in Current Sensor.
Applicable to motor overcurrent protection and 3-phase AC current detection.
Inverse-type, start-up lock type, and instantaneous type over,
current sensors avvailable K8AC-H22PN-FLK.
Instantaneous type under current sensor available.
Plug-in design simplifies installation, removal, and wiring.
DIN sized (48 mm x 96 mm).
Pin shape: Solder cup pins.
Applicable wires: AWG26 max.
Minimum order: 200.
Small Round Water-resistive.
Connectors.
Water-resistive, compact connector meets IP67 requirements.
Conventional M8 screw-mounting models are available along with,
S8 snap-in models that connect and disconnect with one touch OMRON K8AC-H22PN-FLK.
Ideal for a wide variety of FA and OA applications K8AC-H22PN-FLK
Connectors on both cable ends require no harness work.
Some new M8 models with 3 or 5 poles. Cable length L: 3.0 m.
Connect Connector-Terminal,
Block Conversion Units (XW2@) to,
I/O Units for Programmable,
Controllers with one touch. I/O classification: Output.
I/O points: 16.
Internal I/O circuit common: PNP (– common) OMRON K8AC-H22PN-FLK.
Rated voltage: 12 VDC, 24 VDC.
Single Cable Connection to PLC Means.
Space is Saved and Less Control Panel.
Wiring is Required.
Compact size: 182 (W) 85 (D) 68 (H) mm,
(8-point Output Block width is 102 mm).
Connects to the PC through the connecting cable,
(G79 Series) and connector, and requires only a,
snap-in operation.
Surge suppressor circuit built-in OMRON K8AC-H22PN-FLK.
Immediate recognition of I/O signal status using,
LED operation indicators.
G3TA I/O Solid-state relay can be mounted instead,
of G7T.
Mounts easily on a DIN track.
Approved by UL, CSA (except for G7TC-OC16-1). Servo trunk unit.
Product Name: servo relay unit.
Application unit: FQM1-MMA22/MMP22, CS1W-HCP22-V1.
Specifications: -.
Axis number: biaxial.
The connector and terminal of the relay unit are integrated into a whole,
Save the wiring servo drive and position control unit.
Servo driver and control signal of position control unit,
Simple wiring on terminal stage.
The connector without soldering, with only a screwdriver can wiring.
Dedicated connection cable between units.
DIN guide rail installation, the rapid installation, screw installation of two methods.
M3.0 thread terminals attached with a special plate signal.
The terminal can be confirmed by the signal name. Terminal/mounting: Plug-in/DIN rail via socket.
Control voltage: 100/110 VDC.
Under currennt detection: Instantaneous type K8AC-H22PN-FLK.
Solid-state, Plug-in Current Sensor.
Applicable to motor overcurrent protection and 3-phase AC current detection.
Inverse-type, start-up lock type, and instantaneous type over,
current sensors avvailable K8AC-H22PN-FLK.
Instantaneous type under current sensor available.
Plug-in design simplifies installation, removal, and wiring.
DIN sized (48 mm x 96 mm).
...More relevant models >>>>
Last one: OMRON Digital Heater Element Burnout Detector K8AC-H22PC-FLK
next one: OMRON Digital Heater Element Burnout Detector K8AC-H23CC-FLK
Related download