Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGDV-____25 Type (Used by linear servo motor)
>> SGDV-3R8A25A Servo driver for linear servo motor Yaskawa SGDV-3R8A25A
SGDV-3R8A25A Servo driver for linear servo motor Yaskawa SGDV-3R8A25A
Brand:
Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-3R8A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Name: Servo driver for linear servo motor
Model: SGDV-3R8A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space Yaskawa SGDV-3R8A25A.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGDV-3R8A25A
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters Yaskawa SGDV-3R8A25A.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key Yaskawa SGDV-3R8A25A.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-3R8A25A Yaskawa.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2 SGDV-3R8A25A Yaskawa.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard) SGDV-3R8A25A Yaskawa.
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installattion method: flange type SGDV-3R8A25A.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) Yaskawa SGDV-3R8A25A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space Yaskawa SGDV-3R8A25A.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGDV-3R8A25A
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters Yaskawa SGDV-3R8A25A.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key Yaskawa SGDV-3R8A25A.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-3R8A25A Yaskawa.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2 SGDV-3R8A25A Yaskawa.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard) SGDV-3R8A25A Yaskawa.
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installattion method: flange type SGDV-3R8A25A.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) Yaskawa SGDV-3R8A25A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Servo driver for linear servo motor SGDV-2R8A25B002000
next one: Yaskawa Servo driver for linear servo motor SGDV-3R8A25A002000
Related download