Servo motor type SGMAH (speed: 3000r\/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with DC24V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance
Sigma -V series servo motor SGMPS.
Rated output: 200W (0.2KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive Yaskawa SGMAH-08A1A2C.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1
SGMAH-08A1A2C5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C Yaskawa SGMAH-08A1A2C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor Yaskawa SGMAH-08A1A2C.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min SGMAH-08A1A2C Yaskawa.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMAH-08A1A2C Yaskawa.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type) SGMAH-08A1A2C Yaskawa.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation oof the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMAH-08A1A2C.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) Yaskawa SGMAH-08A1A2C.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.