Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMPS type motor
>> SGMPS-01ACE2EE Yaskawa Medium inertia flat type motor
SGMPS-01ACE2EE Yaskawa Medium inertia flat type motor
Brand:
Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-01ACE2EE
Sigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Medium inertia flat type motor
Model: SGMPS-01ACE2EE
Sigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Interface: MECHATROLINK-III communication command type (rotary servo motor) SGMPS-01ACE2EE Yaskawa.
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series SGMPS-01ACE2EE
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control SGMPS-01ACE2EE Yaskawa. Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Optional (hardware): rack mounting type.
Matching (software): standard SGMPS-01ACE2EE Yaskawa.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Optional (hardware): rack mounting type.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needss 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-01ACE2EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMPS-01ACE2EE.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Interface: MECHATROLINK-III communication command type (rotary servo motor) SGMPS-01ACE2EE Yaskawa.
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series SGMPS-01ACE2EE
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control SGMPS-01ACE2EE Yaskawa. Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (linear servo motor).
Optional (hardware): rack mounting type.
Matching (software): standard SGMPS-01ACE2EE Yaskawa.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Optional (hardware): rack mounting type.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needss 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-01ACE2EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMPS-01ACE2EE.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Last one: Yaskawa Medium inertia flat type motor SGMPS-15ACE2CE
next one: Yaskawa Medium inertia flat type motor SGMPS-02ACE2EE
Related download