LK166
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____11 Type (used by rotary type servo motor) >> Servo drive MECHATROLINK- II communication command type SGDV-5R4D11A Yaskawa SGDV-5R4D11A

Servo drive MECHATROLINK- II communication command type SGDV-5R4D11A Yaskawa SGDV-5R4D11A

Brand: Yaskawa
Name: Servo drive MECHATROLINK- II communication command type
Model: SGDV-5R4D11A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
Ultra high power response series: the need for small inertia, high torque Yaskawa SGDV-5R4D11A.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGDV-5R4D11A
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals Yaskawa SGDV-5R4D11A.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware gaugeSigma -V series servo motor SGMPS Yaskawa SGDV-5R4D11A.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V) SGDV-5R4D11A Yaskawa.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1 SGDV-5R4D11A Yaskawa. 5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGDV-5R4D11A Yaskawa.
Excitation mode: permanent magnet type.
Installattion method: flange type SGDV-5R4D11A.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) Yaskawa SGDV-5R4D11A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation


...More relevant models >>>>