LK166
Home >> Price >> OMRON >> MM4XP DC125
Brand sort

OMRON MM4XP DC125

No PHOTO
Brand: OMRON
Country: JAPAN
Name:
Model: MM4XP DC125
Market price: U.S.$ 87.98
(The following are the market open price not sales price!)
OMRON MM4XP DC125
Size: 96 x 96mm.
Ontology: terminal type, temperature input type.
Category: control output 1 point type (power supply AC100 ~ 240V).
Shell color: black.
Control output: voltage output (SSR driver).
Control mode: standard or heating cooling.
Auxiliary output points: 3 points.
Heater with broken wire, SSR fault, heater over current detection function /ES1B power supply: single phase heater with detection function MM4XP DC125
Event input points: -.
Transfer output: -.
Communication: -.
The general temperature controller 96mm, 48 * 96mm square has been upgraded to improve the performance and function of /.
Indicates that the accuracy of the upgrade, increase the function of prevention and maintenance, further enhance the performance MM4XP DC125.
Add PV/SV state display function, to see the state of the thermostat
(automatic / manual, RUN/STOP, alarm), interactive display PV/SV.
Increase the number of control output ON/OFF counting function, can prevent the maintenance of temperature controller internal relay.
Increased the 3 segment display, which can display the current value / target / operation MM4XP DC125.
Increased the PF key, the distribution of automatic / manual, RUN/STOP, etc . , can be a key operation. Name: System Units; Turnback Units.
Specifications: Right Turnback Unit,
(Mounts to the right side of Slice I/O Terminal.)
Standards: CE, UC1, L, N.
"Easy" and "Flexible" system expansion,
with linked CC-Link and CompoNet.
Branching is easily made with CompoNet.
Wiring material cost can be reduced.
Bit-level I/O distribution reduces,
wiring in the system.
A wide variety of CompoNet Slave Units,
contribute to system size reduction.
Seven-segment Display on the Gateway Unit,
helps to detect errors on site.
The Participation Flags and Communications,
Error Flags can be checked at the Host,
Controller to detect the location and,
content of the error. Time specification: Instantaneous type.
Current setting range: 50 to 160 A.
Operating voltage: 400/440 VAC.
Resetting method: Manual.
Solid-state Relay Enables Choice of Three.
Operating Functions (Overcurrent, Open,
phase, and Reverse-phase).
Protects 3-phase induction motors and their loads from damage.
Selection and combination of operating functions from overcur,
rent, open-phase, and reverse-phase.
Circuit and output relay operation can be checked by just operat,
ing the test button.
The set time value can be checked eeasily because operation time,
is indicated from the start of operation MM4XP DC125.
Space-saving, integrated construction.
Note: If the K2CM is used with an inverter, the operating conditions will,
depend on the load wiring length, inverter carrier frequency, basic,
frequency, annd load conditions MM4XP DC125. Error will occur in the operating,
values of the overload elements. It is recommended to test operation,
before using the K2CM.
MM4XP DC125 Operation manual / Instructions / Catalog download link: /searchDownload.html?Search=MM4XP DC125&select=5


...more relevant model market price >>>>
Related products
OMRON
Power Relay
MM4XP-D
OMRON Power Relay MM4XP-D
Type: DC-switching with uilt-in diode.
OMRON
Power Relay
MM4XPN
OMRON Power Relay MM4XPN
Type: DC-switching with operation indica
OMRON
Power Relay
MM4XP-JD
OMRON Power Relay MM4XP-JD
Type: Conforming to auxiliary power rela
OMRON
Power Relay
MM4XP
OMRON Power Relay MM4XP
Type: DC-switching. Contact form: 4PDT.