Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J4 series
>> MR-J4 servo amplifier
>> MR-J4-100B-RJ010 Servo driver MITSUBISHI MR-J4-100B-RJ010
MR-J4-100B-RJ010 Servo driver MITSUBISHI MR-J4-100B-RJ010
Brand:
MITSUBISHI
Name: Servo driver
Model: MR-J4-100B-RJ010
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 1.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: support for CC-LinkIE.Field network motion control.
Servo amplifier supporting IE Field CC-Link network.
Ethernet based open network, support for motion control.
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting.
...More relevant models >>>>
Name: Servo driver
Model: MR-J4-100B-RJ010
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 1.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: support for CC-LinkIE.Field network motion control.
Servo amplifier supporting IE Field CC-Link network.
Ethernet based open network, support for motion control.
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting.
Servo motor series: low inertia, medium / high power.
Rated output: 1.5kw.
Rated speed: 3000r/min.
Electromagnetic brake: with.
Shaft end specification: Standard (straight axis).
Voltage: 400V level.
Features: low inertia for high speed / acceleration and deceleration operation occasions.
IP level: IP67 MITSUBISHI MR-J4-100B-RJ010.
Application example:
1, food processing machinery.
2, printing machine MR-J4-100B-RJ010
3, injection molding machine (11KW, 15KW).
4, large press machine (11KW, 15KW).
The protection level of the HF-SP/HF-JP series servo motor is IP67 (except the shaft part).
Low inertia of the power servo motor (0.5kW ~ 9kW), the maximum speed: 6000r/min (rated speed: 3000r/min),
Suitable for high frequency positioning and acceleration / deceleration operations, especially for food processing machines and printing machines MITSUBISHI MR-J4-100B-RJ010.
Low inertia, high power, no cooling fan servo motor (11kW and 15kW), maximum speed: 3000r/min (rated speed: 1500r/min).
The motor structure is more compact due to the adoption of the non cooling fan design, and the connection is reduced by using the power source connector.
(compared with the HF-LP series servo motor with the same power, the volume is reduced by about 46%, and the weight is reduced by about 34%,
Suitable for high frequency positioning and acceleration / deceleration operations, especially for injection molding machines and large presses MITSUBISHI MR-J4-100B-RJ010 MR-J4-100B-RJ010 MITSUBISHI.
HF-JP703 (4) /903 (4) maximum speed: 5000r/min. Drive: MR-H_ACN series built-in positioning function.
Rated output: 0 MR-J4-100B-RJ010 MITSUBISHI. 2KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MR-J4-100B-RJ010 MITSUBISHI.
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting the minimum detectable speed MR-J4-100B-RJ010.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is largger MITSUBISHI MR-J4-100B-RJ010.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method.
Rated output: 1.5kw.
Rated speed: 3000r/min.
Electromagnetic brake: with.
Shaft end specification: Standard (straight axis).
Voltage: 400V level.
Features: low inertia for high speed / acceleration and deceleration operation occasions.
IP level: IP67 MITSUBISHI MR-J4-100B-RJ010.
Application example:
1, food processing machinery.
2, printing machine MR-J4-100B-RJ010
3, injection molding machine (11KW, 15KW).
4, large press machine (11KW, 15KW).
The protection level of the HF-SP/HF-JP series servo motor is IP67 (except the shaft part).
Low inertia of the power servo motor (0.5kW ~ 9kW), the maximum speed: 6000r/min (rated speed: 3000r/min),
Suitable for high frequency positioning and acceleration / deceleration operations, especially for food processing machines and printing machines MITSUBISHI MR-J4-100B-RJ010.
Low inertia, high power, no cooling fan servo motor (11kW and 15kW), maximum speed: 3000r/min (rated speed: 1500r/min).
The motor structure is more compact due to the adoption of the non cooling fan design, and the connection is reduced by using the power source connector.
(compared with the HF-LP series servo motor with the same power, the volume is reduced by about 46%, and the weight is reduced by about 34%,
Suitable for high frequency positioning and acceleration / deceleration operations, especially for injection molding machines and large presses MITSUBISHI MR-J4-100B-RJ010 MR-J4-100B-RJ010 MITSUBISHI.
HF-JP703 (4) /903 (4) maximum speed: 5000r/min. Drive: MR-H_ACN series built-in positioning function.
Rated output: 0 MR-J4-100B-RJ010 MITSUBISHI. 2KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MR-J4-100B-RJ010 MITSUBISHI.
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting the minimum detectable speed MR-J4-100B-RJ010.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is largger MITSUBISHI MR-J4-100B-RJ010.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method.
...More relevant models >>>>
Last one: 
next one: Related download