Home
>> Products
>> MITSUBISHI
>> FX series PLC
>> FX3SA series
>> PLC FX3SA-30MT-CM MITSUBISHI FX3SA-30MT-CM
PLC FX3SA-30MT-CM MITSUBISHI FX3SA-30MT-CM
Brand:
MITSUBISHI
Name: PLC
Model: FX3SA-30MT-CM
Input and output points: 30 points.
Power supply: AC100-240V.
Input points: 16 points.
Output points: 14 points.
Output form: transistor output (drain).
Power consumption: 21W.
Weight: 0.45KG.
Outline dimension: 100x90x75mm.
A new application model.
FX3SA is a basic model on the basis of the basic performance of FX1S above the expansion of the expansion of the new model.
FX3SA is applicable to all kinds of fields of small scale equipment which need to simulate the quantity and function of MODBUS and Ethernet.
Basic models suitable for small scale control.
Compact but powerful,
At the same time, the analog quantity and communication function, etc..
...More relevant models >>>>
Name: PLC
Model: FX3SA-30MT-CM
Input and output points: 30 points.
Power supply: AC100-240V.
Input points: 16 points.
Output points: 14 points.
Output form: transistor output (drain).
Power consumption: 21W.
Weight: 0.45KG.
Outline dimension: 100x90x75mm.
A new application model.
FX3SA is a basic model on the basis of the basic performance of FX1S above the expansion of the expansion of the new model.
FX3SA is applicable to all kinds of fields of small scale equipment which need to simulate the quantity and function of MODBUS and Ethernet.
Basic models suitable for small scale control.
Compact but powerful,
At the same time, the analog quantity and communication function, etc..
Output points: 16 points.
Power supply: the basic unit to the expansion module to provide power.
Output form: transistor output (source).
Terminal type: connector type.
Weight: 0.15kg.
FX3GC, FX3UC can be directly connected to the input and output expansion equipment, to achieve a compact expansion.
Can choose 16 points, 32 points of the relay or transistor input and output models MITSUBISHI FX3SA-30MT-CM FX3SA-30MT-CM
FX2NC-16E_-T-DS for terminal units can be disassembled models. Max input / output points: 64 points.
Power supply voltage: 24VDC.
Input points: 32 points.
Output points: 32 points.
Output type: relay.
Power consumption: 35W.
Weight (kg):1.0.
Size (WxHxD) mm:220x90x87.
Note recording function, Component annotation can be recorded in the program register MITSUBISHI FX3SA-30MT-CM.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MITSUBISHI FX3SA-30MT-CM.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017) FX3SA-30MT-CM MITSUBISHI. Axis of control: 1.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF) FX3SA-30MT-CM MITSUBISHI.
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
7 operating modules required for easy positioning control are provided.
Type of instruction, please refer to the list in front of you.
One can control a shaft.
FX3U, PLC FX2N can connect up to 8 units,
PLC FX2NC can connect up to 4 units,
PLC FX3UC can connect up to 7 units, so that it can control more than one independent axis FX3SA-30MT-CM MITSUBISHI.
Maximum can output 100kHz pulse train.
Positioning control through the control program. Protocol: SLMP, TCP/IP, UDP, SNTP.
Communication mode: full duplex / half duplex.
At the same time cann open a few: 4 connection FX3SA-30MT-CM.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried outt by Works2 GX in a place far from the scene MITSUBISHI FX3SA-30MT-CM.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board.
Power supply: the basic unit to the expansion module to provide power.
Output form: transistor output (source).
Terminal type: connector type.
Weight: 0.15kg.
FX3GC, FX3UC can be directly connected to the input and output expansion equipment, to achieve a compact expansion.
Can choose 16 points, 32 points of the relay or transistor input and output models MITSUBISHI FX3SA-30MT-CM FX3SA-30MT-CM
FX2NC-16E_-T-DS for terminal units can be disassembled models. Max input / output points: 64 points.
Power supply voltage: 24VDC.
Input points: 32 points.
Output points: 32 points.
Output type: relay.
Power consumption: 35W.
Weight (kg):1.0.
Size (WxHxD) mm:220x90x87.
Note recording function, Component annotation can be recorded in the program register MITSUBISHI FX3SA-30MT-CM.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy to operate.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program MITSUBISHI FX3SA-30MT-CM.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017) FX3SA-30MT-CM MITSUBISHI. Axis of control: 1.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF) FX3SA-30MT-CM MITSUBISHI.
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
7 operating modules required for easy positioning control are provided.
Type of instruction, please refer to the list in front of you.
One can control a shaft.
FX3U, PLC FX2N can connect up to 8 units,
PLC FX2NC can connect up to 4 units,
PLC FX3UC can connect up to 7 units, so that it can control more than one independent axis FX3SA-30MT-CM MITSUBISHI.
Maximum can output 100kHz pulse train.
Positioning control through the control program. Protocol: SLMP, TCP/IP, UDP, SNTP.
Communication mode: full duplex / half duplex.
At the same time cann open a few: 4 connection FX3SA-30MT-CM.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried outt by Works2 GX in a place far from the scene MITSUBISHI FX3SA-30MT-CM.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board.
...More relevant models >>>>
Last one: 
next one: Related download